How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
This post listed below pertaining to Installing A Bathtub is unquestionably captivating. You should see for yourself.
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably challenging project. If the old tub is easily available, the project can move speedily; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the job is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually qualified yourself for the work and also are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed task, it is far better to think about employing one before you begin. Chances are you might need a professional plumber to make tube connections.
This short article will help you install a brand-new tub in your restroom if you have actually already acquired a brand-new bathtub and also do not need to transform the arrangement of your previous water pipes.
Your tools as well as material list must make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water staying in the system. The process of eliminating the existing faucets can be fairly troublesome due to the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before carrying on to fit the new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wooden boards under its feet, place the bathtub in the required placement. The wooden boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the tub up until the spirit level reviews level.
To install taps, fit all-time low of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the bath tub and also examine the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait until the bath tub has actually been utilized at least when as this will certainly settle it right into its final position.
Preparing for the Installment
To start with, the sustaining structure provided with the bathroom should be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, resulting in issues with moisture as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can split fairly very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our excerpt on How to Install a Bathtub. Thanks so much for spending some time to read through our article post. Appreciated our post? Please share it. Let somebody else check it out. Thank you for your time. Kindly check our blog back soon.
Apply Now Report this page